티스토리 뷰

운영체제/리눅스

[CentOS] HDD 속도 측정

메모하는습관 2011.03.29 03:38
> hdparm -tT /dev/sda

/dev/sda:
 Timing cached reads:   20724 MB in  2.00 seconds = 10375.81 MB/sec
 Timing buffered disk reads:  304 MB in  3.02 seconds = 100.60 MB/sec




> hdparm --help

hdparm - get/set hard disk parameters - version v6.6

Usage:  hdparm  [options] [device] ..

Options:
 -a   get/set fs readahead
 -A   set drive read-lookahead flag (0/1)
 -b   get/set bus state (0 == off, 1 == on, 2 == tristate)
 -B   set Advanced Power Management setting (1-255)
 -c   get/set IDE 32-bit IO setting
 -C   check IDE power mode status
 -d   get/set using_dma flag
 --direct  use O_DIRECT to bypass page cache for timings
 -D   enable/disable drive defect management
 -E   set cd-rom drive speed
 -f   flush buffer cache for device on exit
 -g   display drive geometry
 -h   display terse usage information
 -i   display drive identification
 -I   detailed/current information directly from drive
 --Istdin  read identify data from stdin as ASCII hex
 --Istdout write identify data to stdout as ASCII hex
 -k   get/set keep_settings_over_reset flag (0/1)
 -K   set drive keep_features_over_reset flag (0/1)
 -L   set drive doorlock (0/1) (removable harddisks only)
 -M   get/set acoustic management (0-254, 128: quiet, 254: fast) (EXPERIMENTAL)
 -m   get/set multiple sector count
 -n   get/set ignore-write-errors flag (0/1)
 -p   set PIO mode on IDE interface chipset (0,1,2,3,4,...)
 -P   set drive prefetch count
 -q   change next setting quietly
 -Q   get/set DMA tagged-queuing depth (if supported)
 -r   get/set device  readonly flag (DANGEROUS to set)
 -R   register an IDE interface (DANGEROUS)
 -S   set standby (spindown) timeout
 -t   perform device read timings
 -T   perform cache read timings
 -u   get/set unmaskirq flag (0/1)
 -U   un-register an IDE interface (DANGEROUS)
 -v   defaults; same as -mcudkrag for IDE drives
 -V   display program version and exit immediately
 -w   perform device reset (DANGEROUS)
 -W   set drive write-caching flag (0/1) (DANGEROUS)
 -x   tristate device for hotswap (0/1) (DANGEROUS)
 -X   set IDE xfer mode (DANGEROUS)
 -y   put IDE drive in standby mode
 -Y   put IDE drive to sleep
 -Z   disable Seagate auto-powersaving mode
 -z   re-read partition table
 --security-help  display help for ATA security commands

'운영체제 > 리눅스' 카테고리의 다른 글

[CentOS] yum을 이용해 tomcat 6.0.35 설치  (0) 2012.05.08
CVS, SVN 폴더 삭제  (0) 2012.05.04
sudo 설정 (sudoers)  (0) 2012.05.04
[CentOS] HDD 속도 측정  (0) 2011.03.29
[CentOS 5.5] yum을 이용한 samba 설치  (0) 2011.03.29
iostat  (0) 2010.06.16
댓글
댓글쓰기 폼